So the version that comes with the Ultimate gets the job done, but it is old and doesn't have many features. The new version of Cura doesn't work out of the box, and needs to be tweaked to work properly. So here you're going to learn what you need to do to make Cura work perfectly with this printer!
Creative Anger is a new channel dedicated to technology, science, and the arts. Link to Cura Download: https://ultimaker.com/en/products/ultimaker-cura-softw. Download cura windows 10 for free. Photo & Graphics tools downloads - Cura by Cura and many more programs are available for instant and free download. The Voxel is a unique, easy to use, beginner-friendly 3D printer that brings 3D printing to the masses with its simple menu system displayed on a 2.8' color IPS touch screen.
Firstly, you're going to need to go into the Cura machine settings and add a new custom printer.
Here's an image of what your settings should look like: http://imgur.com/a/kyDjg
Then you're going to want to replace those START/STOP Gcode lines in the machine settings with a custom set of codes in to the appropriate panel. You put the start gcode in the left panel, and the stop gcode in the right panel. Easy enough. Make sure to erase anything that was there previously. .
;START GCODE
;Sliced at: {day} {date} {time}
G21 ;metric values
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z15.0 F{travel_speed} ;move the platform down 15mm
G92 E0 ;zero the extruded length
G1 F140 E30 ;extrude 3mm of feed stock
G1 X20 Y0 F140 E30
G92 E0 ;zero the extruded length again
G1 F{travel_speed}
M117 Printing..
;END GCODE
M104 S0 ;extruder heater off
M140 S0 ;heated bed heater off (if you have it)
G91 ;relative positioning
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
G28 X0 Y0
G90
G1 Z160 ;move X/Y to min endstops, so the head is out of the way
M84 ;steppers off
G90 ;absolute positioning
Now here are the final guideline settings: http://imgur.com/a/jUAoo
Some of these can be changed to user preference, like print speed, layer height, etc..these settings are primarily meant to give you the proper raft settings, since the default raft settings in Cura do not work properly at all with this printer. These settings will make a really good raft for when you need one. The other settings, like travel speed and print speed, are what I personally consider a good middle ground that doesn't push things too much and doesn't produce quality issues for basic prints. These settings could very well be bumped up, or lowered, as needed, so only take them as a guide rather than a limit.
Website: https://ultimaker.com/en/products/ultimaker-cura-software
Cura is 3D slicing software from Ultimaker that prepares a 3D model for printing, suitable for use with students at Upper KS2 and beyond.
Cura is simple but powerful 3D slicing software produced by Ultimaker. The print profiles are optimised for Ultimaker 3D printers, but the softwre will slice 3D files for any 3D printer brand/model. The software s Top free video editing software. upports STL, 3MF and OBJ 3D file formats and also has a function that will import and convert 2D images (.JPG .PNG .BMP and .GIF) to 3D extruded models. The software will allow you to open and place multiple models on the print bed (each with different slicing settings if required). This allows you to print multiple models at a time, making classroom management of the printing process simpler.
Firstly, you're going to need to go into the Cura machine settings and add a new custom printer.
Here's an image of what your settings should look like: http://imgur.com/a/kyDjg
Then you're going to want to replace those START/STOP Gcode lines in the machine settings with a custom set of codes in to the appropriate panel. You put the start gcode in the left panel, and the stop gcode in the right panel. Easy enough. Make sure to erase anything that was there previously. .
;START GCODE
;Sliced at: {day} {date} {time}
G21 ;metric values
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z15.0 F{travel_speed} ;move the platform down 15mm
G92 E0 ;zero the extruded length
G1 F140 E30 ;extrude 3mm of feed stock
G1 X20 Y0 F140 E30
G92 E0 ;zero the extruded length again
G1 F{travel_speed}
M117 Printing..
;END GCODE
M104 S0 ;extruder heater off
M140 S0 ;heated bed heater off (if you have it)
G91 ;relative positioning
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
G28 X0 Y0
G90
G1 Z160 ;move X/Y to min endstops, so the head is out of the way
M84 ;steppers off
G90 ;absolute positioning
Now here are the final guideline settings: http://imgur.com/a/jUAoo
Some of these can be changed to user preference, like print speed, layer height, etc..these settings are primarily meant to give you the proper raft settings, since the default raft settings in Cura do not work properly at all with this printer. These settings will make a really good raft for when you need one. The other settings, like travel speed and print speed, are what I personally consider a good middle ground that doesn't push things too much and doesn't produce quality issues for basic prints. These settings could very well be bumped up, or lowered, as needed, so only take them as a guide rather than a limit.
Website: https://ultimaker.com/en/products/ultimaker-cura-software
Cura is 3D slicing software from Ultimaker that prepares a 3D model for printing, suitable for use with students at Upper KS2 and beyond.
Cura is simple but powerful 3D slicing software produced by Ultimaker. The print profiles are optimised for Ultimaker 3D printers, but the softwre will slice 3D files for any 3D printer brand/model. The software s Top free video editing software. upports STL, 3MF and OBJ 3D file formats and also has a function that will import and convert 2D images (.JPG .PNG .BMP and .GIF) to 3D extruded models. The software will allow you to open and place multiple models on the print bed (each with different slicing settings if required). This allows you to print multiple models at a time, making classroom management of the printing process simpler.
Cura is desktop software that can be downloaded free of charge from the Ultimaker website and is available for Windows, Mac and Linux.
Monoprice Mp10 Cura Driver
We recommend Cura as the default slicing software for all schools as it is free of charge, powerful, quick to slice and very easy to get started with. Students in upper KS2 and beyond after some instruction can independently use the software to slice using the default profiles. However although simple to learn, the software contains over 200 expert settings, so more advanced users can tinker with the settings to produce prints of the quality they require.
Learn Cura
There are a number of online resources available to help teachers and students to learn Cura.
The Ultimaker website contains a comprehensive online Cura Manual, containing everything you need to know to use Cura, it also contains downloadable PDF quick start guides. In addition to this you can access a number of Cura Quick Start Video Guides on the Ultimaker YouTube channel.
Virusscanner macbook gratis. The CREATE Education Project use Cura as the default slicing software as it is free to download, powerful but quick to slice and simple to get started with. As each project may require different slicing settings in Cura, CREATE Education provide detailed slicing settings where required in all our project teacher guides to make learning and using the software even easier for beginners. We also provide a number of Cura specific resources to help you to learn some of the software features.
Monoprice 3d Printer Cura Software
Note: Please bear in mind that recently the Cura software has developed further and has a new interface. This means that the screenshots in our older resources may not appear to look like the current version – however any functionality described in the resource still exists in the current version.
